Theory: Fuel Temperatures and Boiling Limits

Why Thermal Limits Matter

A reactor's power is limited not by its neutrons but by its heat removal. Two limits protect the fuel. The fuel centreline temperature must stay well below the melting point of uranium dioxide. The cladding surface must stay in nucleate boiling, never reaching the critical heat flux (CHF), where a steam blanket forms, heat transfer collapses, and the cladding overheats. Thermal-hydraulics engineers check these limits for every core design, and the plant's technical specifications turn them into limits on linear heat rate and on the departure from nucleate boiling ratio (DNBR).

Heat Flow Out of a Fuel Rod

Heat generated in the pellet flows outward through four regions in series: the fuel itself, the helium-filled gap, the zirconium-alloy cladding, and the coolant film on the cladding surface. For a rod with a linear heat rate q′ (heat per unit length), each temperature drop is proportional to q′. The fuel drop does not depend on the pellet size at all. The gap drop shrinks later in life as the pellet swells and the gap closes.

Temperature Drops in a Fuel Rod (q′ in W/cm) Coolant film: ΔT = q′ / (2π r_co h)     Cladding: ΔT = q′ ln(r_co/r_ci) / (2π k_c)
Gap: ΔT = q′ / (2π r_f h_gap)     Fuel: ΔT = q′ / (4π k_f)
T_CL = T_coolant + ΔT_film + ΔT_clad + ΔT_gap + ΔT_fuel
Most of the temperature drop is inside the low-conductivity UO₂

Departure from Nucleate Boiling

At moderate heat flux, small bubbles form and collapse on the cladding, which removes heat very well. As the heat flux rises, the bubbles crowd together until, at the CHF, they merge into a vapour film. The cladding temperature then jumps by hundreds of degrees. CHF depends on the flow, pressure, and subcooling, and it is measured in heated-rod test loops; the results are fitted into correlations used in design. The DNBR compares CHF with the actual heat flux on the hottest rod and must stay above a limit, typically about 1.3.

Heat Flux and DNBR Surface heat flux: q″ = q′ / (2π r_co)   (1 W/cm² = 0.01 MW/m²)
DNBR = q″_CHF / q″_actual ≥ 1.30
Highest allowed q′ = (q″_CHF / 1.30) × 2π r_co
More flow and more subcooling raise the CHF

Data Used in This Lab

QuantityValueQuantityValue
Pellet radius r_f0.4096 cmCladding radii r_ci; r_co0.418; 0.475 cm
Film coefficient h3.4 W/cm²·KCladding conductivity k_c0.17 W/cm·K
Gap conductance h_gap0.57 (open) or 1.0 (closed) W/cm²·KUO₂ conductivity k_f0.030 W/cm·K
UO₂ melting pointabout 2800 °CDNBR design limit1.30

Property values are representative of a 17 × 17 PWR rod and follow the DOE Fundamentals Handbook (Heat Transfer, Fluid Flow, and Thermodynamics). The CHF in the test loop follows a simplified training correlation, CHF ≈ 2.6 (G/3500)^0.6 (1 + 0.02 ΔT_sub) MW/m², with a few percent of measurement scatter; licensing analyses use correlations such as W-3 or WRB-1.

Core design

Designers set peaking-factor and power limits so both thermal limits hold in normal operation and anticipated transients.

Fuel vendors

Vendors run CHF tests on new grid and mixing-vane designs to raise the allowable power.

Operations

Reactor trips on low flow, high temperature, and overpower protect the DNBR limit automatically.

Temperature and DNBR Profiles

Inside the pellet, heat is generated everywhere, so the temperature falls as a parabola, T(r) = T_CL − (T_CL − T_s)(r/r_f)², with T_s the pellet surface temperature. Outside the pellet no heat is generated, so the drops across the gap, the cladding, and the film are short and steep. Along a channel of length L the heat flux follows roughly q′(z) = q′_max sin(πz/L), and the coolant temperature rises as T(z) = T_in + (ΔT/2)[1 − cos(πz/L)], where ΔT = (2Lq′_max/π)/(ṁ c_p). The local CHF falls as the coolant gets closer to saturation, so the minimum DNBR lies above mid-height, not at the peak heat flux.

Apparatus

The fuel components and test equipment behind thermal limits. In the simulation these are modelled for you, and the readings correspond to what each would report.

Fuel rod cross-section
Pellet, helium gap, cladding, and coolant, the four layers the heat must cross.
Thermocouples
Instrumented test rods carry thermocouples to measure centreline and cladding temperatures.
CHF test loop
An electrically heated rod bundle in a loop that reproduces reactor pressure, flow, and temperature.
3.64 MW/m²
Heater power supply
Raises the rod heat flux in small steps; trips automatically when the cladding temperature jumps.
Grid spacers
Mixing vanes stir the coolant and raise the CHF of the fuel assembly.
MDNBR 1.84q′max 590
Core monitoring system
Calculates the minimum DNBR and peak linear heat rate continuously from in-core data.

Instructions: Running the Virtual Experiment

You are the thermal-hydraulics engineer verifying the core's thermal margins. The simulation has two immersive 3D work areas and two graph work areas. The parts build from undergraduate work in Parts A and B to graduate-level analysis in the last step of Parts C and D; the level of each part is shown beside its title. In each one you set the conditions, work out the answer yourself, enter it, and press Check. Record every reading and calculation in your lab report tables (modelled in the Example Report), with a labelled screenshot of each setup. Drag in any 3D view to orbit, and scroll to zoom. Use the data table in the Theory section.

Part A: Fuel Rod Temperature Profile (3D Fuel Rod Cross-Section)Undergraduate
1
Open Simulation → 3D Fuel Rod Cross-Section. Set q′ = 183 W/cm, T_c = 310 °C, and an open gap. Check the film, cladding, gap, and fuel temperature drops one at a time.
2
Check the centreline temperature and the margin to melting. Compare your numbers with the board's temperature profile. Press Record this run.
3
Repeat at 400 and 590 W/cm, then at 590 W/cm with a closed gap. Record all four in Table A and explain which layer controls the centreline temperature.
Part B: Critical Heat Flux and DNBR (3D CHF Test Loop)Undergraduate
1
Open 3D CHF Test Loop. Set G = 3500 kg/m²·s, subcooling 20 °C, and the plant hot rod at 590 W/cm. Press Ramp heater until DNB and record the measured CHF.
2
Check the hot-rod heat flux, the DNBR, and the highest allowed q′. Press Record this run.
3
Repeat the test at G = 2500 (20 °C) and at 5 °C subcooling (G = 3500). Record them in Table B and explain why a loss of flow or a rise in inlet temperature threatens the DNB limit.
Part C: Radial Temperature Profile (Graph: Radial Temperature)Upper undergraduateGraduate step
1
Open Graph: Radial Temperature. Set 400 W/cm, the open gap, and r = 0.20 cm. Check the pellet surface temperature, the temperature at r, and the fraction of the rise inside the UO₂. Press Record this run.
2
At 400 W/cm, check the temperature at r = 0 and r = 0.30 cm. Then check 183 W/cm and 590 W/cm at r = 0.20 cm, and 590 W/cm with the closed gap. Record every run in Table C.
3
Take a labelled screenshot of the 590 W/cm profile with the melting line. Note in your report where the steepest drops are.
4
GraduateUO₂ conducts heat less well as it gets hotter. At 400 W/cm and 590 W/cm (open gap), and at 590 W/cm with the closed gap, check the centreline temperature with k(T) using the conductivity integral. Compare it with the constant-k result and record both under Table C. Decide whether the constant-k estimate is conservative.
Part D: Hot-Channel Axial Profile (Graph: Hot-Channel Axial Profile)Upper undergraduateGraduate step
1
Open Graph: Hot-Channel Axial Profile. Set q′_max = 450 W/cm, G = 3500 kg/m²·s, and T_in = 285 °C. Check the coolant outlet temperature. Then use the graph and its data table to check the minimum DNBR and the height where it occurs. Press Record this run.
2
Change one setting at a time: G = 4000 and 4500 kg/m²·s; T_in = 280 °C; q′_max = 400 and 350 W/cm (each with the other settings as in step 1). Check and record each case in Table D.
3
Explain in your report why the minimum DNBR is above mid-height rather than at the peak heat flux.
4
GraduateDesign analyses add hot-channel factors that the nominal profile ignores. For the step 1 case and for G = 4500 kg/m²·s, check the minimum DNBR with hot-channel factors (heat flux × 1.03, flow × 0.95). Record the results under Table D and work out what fraction of the DNBR margin above 1.30 the factors use.

Simulation: Fuel Rod Temperatures, CHF Test Loop, and Thermal-Hydraulic Graphs

Core Thermal-Hydraulics Virtual LabSet up the equipment, work out your answer, then Check

Heat made in the pellet flows outward through four layers in series. For each layer the temperature drop is proportional to the linear heat rate q′. Part A uses this work area.

About this work area: The fuel rod cross-section shows the pellet, the gap, the cladding, and the coolant. You set the linear heat rate, the coolant temperature, and whether the pellet-cladding gap is open (fresh fuel) or closed (later in life). The Readings panel gives the rod dimensions and the heat-transfer properties, and every change is announced.

Setup

Readings

Pellet radius r_f—
Cladding inner / outer radius—
Film coefficient h—
Cladding conductivity k_c—
Fuel conductivity k_f—
UO₂ melting point—

Fuel conductivity is taken as constant; in real UO₂ it falls as temperature rises.

Work it out, then check

Table A: your fuel temperature record
q′ (W/cm)GapΔT filmΔT cladΔT gapΔT fuelT_CL (°C)Margin (°C)

The test loop finds the critical heat flux (CHF) for given flow conditions. Compare it with the heat flux on the hottest rod in the plant: the DNB ratio must stay above 1.30. Part B uses this work area.

About this work area: The test loop is a heated rod in a flow channel that reproduces reactor conditions. You set the mass flux and the inlet subcooling, then ramp the heater until departure from nucleate boiling. You also set the plant hot-rod linear heat rate. The Readings panel gives the measured critical heat flux, the cladding radius, and the DNBR limit, and every test is announced.

Setup

Readings

Measured critical heat flux—
Cladding outer radius r_co—
DNBR design limit—
Test status—

Heat flux on the cladding surface: q″ = q′/(2π r_co). 1 W/cm² = 0.01 MW/m².

Work it out, then check

Table B: your DNB record
G (kg/m²·s)Subcooling (°C)CHF (MW/m²)q′ (W/cm)q″ (MW/m²)DNBRMax q′ (W/cm)

The temperature drops you calculated in Part A fit together into one profile across the rod. Inside the pellet the temperature falls as a parabola: T(r) = T_CL − (T_CL − T_s)(r/r_f)². Part C uses this work area.

About this work area: This graph work area plots temperature against radius across a fuel rod at the linear heat rate and gap condition you choose, with the coolant at 310 °C. You also choose a radius inside the pellet. The data table below lists the temperature at each radius, and every change is announced.

Setup

Readings

Coolant temperature T_c—
Pellet radius r_f—
Rod data—
Centreline T_CL (from Part A method)—

T_s = T_c + ΔT_film + ΔT_clad + ΔT_gap; T(r) = T_CL − (T_CL − T_s)(r/r_f)².

Work it out, then check

Table C: your radial temperature record
q′ (W/cm)Gapr (cm)T_s (°C)T(r) (°C)T_CL (°C)Fuel fraction

Along the hot channel the heat flux follows a sine shape and the coolant heats up from inlet to outlet. The local CHF falls as the coolant approaches saturation, so the DNBR is lowest above mid-height. Part D uses this work area.

About this work area: This graph work area plots the heat flux, the coolant temperature, and the DNBR along the hot channel for the peak linear heat rate, mass flux, and inlet temperature you choose. The data table below lists the values every 0.3 m, and every change is announced.

Setup

Readings

Heated length—
Flow area per rod—
Coolant c_p; T_sat—
Local CHF—

q′(z) = q′_max sin(πz/L); T(z) = T_in + (ΔT/2)[1 − cos(πz/L)], ΔT = (2Lq′_max/π)/(G A c_p); DNBR(z) = CHF(z)/q″(z). Simplified training model.

Work it out, then check

Table D: your hot-channel record
q′_max (W/cm)G (kg/m²·s)T_in (°C)ΔT (°C)T_out (°C)Min DNBRz at min (m)

This accessible version provides the same set-up, work-out, and check exercises as the 3D and graph work areas, using native controls, data tables, and screen-reader announcements.

Team Questions

Question 1. A rod runs at q′ = 183 W/cm with r_co = 0.475 cm and h = 3.4 W/cm²·K. What is the coolant film temperature drop, in °C?
Question 2. With r_f = 0.4096 cm and an open-gap conductance of 0.57 W/cm²·K, what is the gap temperature drop at 183 W/cm, in °C?
Question 3. With k_f = 0.030 W/cm·K, what is the temperature drop across the fuel at 183 W/cm, in °C?
Question 4. The coolant is at 310 °C and the cladding drop is 21.9 °C. Using your answers to Questions 1 to 3, what is the fuel centreline temperature, in °C?
Question 5. What is the surface heat flux on a rod at 590 W/cm (r_co = 0.475 cm), in MW/m²?
Question 6. The measured CHF is 3.64 MW/m². What is the DNBR for that rod?
Question 7: Challenge. With CHF = 3.64 MW/m² and a DNBR limit of 1.30, what is the highest allowed linear heat rate, in W/cm?

Example Lab Report

Sample report showing the expected format and level of detail. Use it as a guide for your own submission, and include labelled screenshots of each setup. Your measured CHF values will differ by a few percent.

Core Thermal-Hydraulics: Fuel Temperatures and DNB Margin

Nuclear Engineering Technology | Section: [Your Section] | Date: [Date]

Lab Members: [Names of all members present]

Purpose

To calculate the temperature drops and centreline temperature of a PWR fuel rod at several linear heat rates and gap conditions, to measure the critical heat flux in a test loop and calculate the DNBR and the highest allowed linear heat rate, and to use graphs of the radial temperature profile and the hot-channel axial profile to locate the limiting points.

Theory

The centreline temperature is the coolant temperature plus the film, cladding, gap, and fuel drops, each proportional to q′. The DNBR is the measured CHF divided by the hot-rod heat flux q″ = q′/(2π r_co), and must be at least 1.30.

T_CL = T_c + q′[1/(2πr_co h) + ln(r_co/r_ci)/(2πk_c) + 1/(2πr_f h_gap) + 1/(4πk_f)]  ·  DNBR = CHF/q″

Table A: Fuel Temperatures (T_c = 310 °C) Undergraduate

q′ (W/cm)GapΔT filmΔT cladΔT gapΔT fuelT_CL (°C)Margin (°C)
183open18.021.9124.7485.49601840
400open39.447.9272.71061.017311069
590open58.170.6402.21565.02406394
590closed58.170.6229.31565.02233567

Table B: CHF and DNBR (hot rod at 590 W/cm, q″ = 1.977 MW/m²) Undergraduate

G (kg/m²·s)Subcooling (°C)CHF (MW/m²)DNBRMax q′ (W/cm)
3500203.6401.841836
2500202.9751.505683
350052.8601.447657

Table C: Radial Temperature Profile (T_c = 310 °C) Upper undergraduateGraduate step

q′ (W/cm)Gapr (cm)T_s (°C)T(r) (°C)T_CL (°C)Fuel fraction
183open0.204758449600.747
400open0.00670173117310.747
400open0.20670147817310.747
400open0.30670116217310.747
590open0.20841203324060.747
590closed0.20668186022330.814

Graduate step: with k(T) = 1/(12.73 + 0.01818 T) W/cm·K, the centreline is 1744 °C at 400 W/cm (constant k: 1731 °C), 2918 °C at 590 W/cm with the open gap (constant k: 2406 °C), and 2512 °C with the closed gap (constant k: 2233 °C). At the hot spot the constant-k estimate is about 500 °C too low, and the open-gap rod would reach the melting point.

T(r) = T_CL − (T_CL − T_s)(r/r_f)². Include a screenshot of the profile at 590 W/cm with the melting line.

Table D: Hot-Channel Axial Profile (L = 3.66 m, simplified training model) Upper undergraduateGraduate step

q′_max (W/cm)G (kg/m²·s)T_in (°C)ΔT (°C)T_out (°C)Min DNBRz at min (m)
450350028555.0340.02.682.23
450400028548.1333.13.082.16
450450028542.8327.83.452.11
450350028055.0335.02.872.20
400350028548.9333.93.182.17
350350028542.8327.83.812.11

Graduate step: with hot-channel factors (q′ × 1.03, G × 0.95) the minimum DNBR falls from 2.68 to 2.42 (outlet 344.6 °C) for the step 1 case, and from 3.45 to 3.16 at G = 4500 kg/m²·s. The factors use about 19% and 14% of the margin above 1.30.

ΔT = (2Lq′_max/π)/(G A c_p) with A = 8.788 × 10⁻⁵ m² and c_p = 6.2 kJ/kg·K. The slider ranges keep the hot-channel outlet at or below 340 °C, below saturation (345 °C), so the single-phase model holds. Values read from the graph may differ by a few percent.

Discussion

At average power the centreline was 960 °C, but at the 590 W/cm hot spot it reached 2406 °C, only 394 °C below melting. About three-quarters of the total temperature rise was inside the UO₂ itself, because its conductivity is about one-sixth that of the cladding; the gap added most of the rest. Closing the gap later in life lowered the centreline by 173 °C. Because the fuel drop q′/(4πk_f) does not depend on pellet size, the linear heat rate, not the power density, sets the melting limit.

The hot rod had a DNBR of 1.84 at rated flow and subcooling. Reducing the flow by 29% cut CHF by 18% and the DNBR to 1.51; reducing the inlet subcooling from 20 to 5 °C lowered it to 1.45. Both are still above 1.30, but they show why reactor coolant pump trips and high inlet temperatures are among the transients the reactor protection system must stop quickly. At rated conditions the melting limit, not DNB, was the tighter limit on q′.

The graphs joined these results together. The radial profile showed a flat-topped parabola inside the pellet and short, steep straight drops across the gap and cladding; about three-quarters of the rise from coolant to centreline was inside the UO₂ at every power with the open gap (81% with the closed gap), so only the fuel conductivity and gap conductance can change the centreline much. Along the hot channel, the minimum DNBR was not at the peak heat flux at mid-height but about 0.4 m above it, where the coolant was hotter and the local CHF lower. Lower flow or a higher peak power raised the outlet temperature and lowered the minimum DNBR, and lower flow moved it further up the channel, which is why core limits are set on flow and inlet temperature as well as on power.

The graduate steps showed where the simple models stop being conservative. Because UO₂ conductivity falls as it heats, the conductivity integral put the hot-spot centreline about 500 °C above the constant-k value, at the melting point with the open gap, so real limits on linear heat rate come from conductivity-integral calculations. Hot-channel factors for heat flux and flow cut the minimum DNBR by about 10%, using up a fifth of the margin, which is why licensing analyses apply them before comparing with the 1.30 limit.

Conclusion

The UO₂ conductivity and gap conductance control the fuel centreline temperature, which limits the peak linear heat rate. CHF rises with flow and subcooling, and the DNBR quantifies the margin to a boiling crisis.

Practice Questions

Show all work and include units. Use the data table in the Theory section.

Question 1
Find the linear heat rate at which the fuel centreline would just reach 2800 °C with an open gap and T_c = 310 °C.
Hint: the total drop is q′ times the sum of the four thermal resistances.
Question 2
Explain why the temperature drop across the fuel does not depend on the pellet radius.
Hint: a bigger pellet has more heat to conduct but a longer path.
Question 3
The cladding surface must stay below about 350 °C to limit corrosion. At what q′ does it reach that temperature with T_c = 320 °C?
Hint: only the film drop lies between the coolant and the cladding surface.
Question 4
Describe what happens to the cladding temperature at DNB, and why CHF tests stop the heater automatically.
Hint: compare heat transfer through a liquid film and a vapour film.
Question 5
A loss of one of four reactor coolant pumps cuts core flow to about 75%. Using the test-loop correlation, estimate the new DNBR for the 590 W/cm hot rod.
Hint: CHF scales as G^0.6.
Question 6: Challenge
Combine your answers: which limit, fuel melting or DNB, would restrict the hot rod first if the core flow fell to 50%? Show both margins.
Hint: flow changes the CHF but hardly changes the fuel temperature drops.