Virginia Research Institute
Virginia Research Institute
Virtual Laboratory  ·  Built by E2 Innovations
← Back to Virtual Labs|Neutron Interactions, Cross Sections, and Moderation
Nuclear Engineering Technology · Reactor Physics: Neutron Behavior

Neutron Interactions, Cross Sections, and Moderation

Work as a reactor physics technician qualifying materials for a research reactor. Fire a collimated thermal-neutron beam through slabs of water, heavy water, graphite, iron, and cadmium, and use atom densities and cross sections to predict how many neutrons get through. Then follow fast fission neutrons as they collide with moderator nuclei, and work out how many collisions each moderator needs to thermalize them and which moderator a reactor designer should choose. Two graph work areas then show the same physics the way engineers read it: a log–log plot of absorption cross section against neutron energy, used to choose detector and control materials, and a slowing-down ladder that compares how fast each moderator brings neutrons to thermal energy. In every part you work out the answer yourself, then check it.

Theory: How Neutrons Interact with Matter

Why Neutrons Matter in a Reactor

A nuclear reactor runs on neutrons. Each fission releases two to three fast neutrons with energies near 2 MeV, and the chain reaction continues only if enough of them cause new fissions. Because neutrons have no charge, they pass through electron clouds untouched and interact only with nuclei. Whether a neutron scatters, is captured, or causes fission depends on the nucleus it meets and on its energy. Reactor engineers describe this with cross sections, and every design decision, from the choice of moderator to the material of the control rods, starts with them.

Types of Neutron Interaction

InteractionWhat happensReactor importance
Elastic scattering (n,n)The neutron bounces off; kinetic energy is shared, the nucleus is not excitedMain slowing-down process in moderators
Inelastic scattering (n,n′)The nucleus is left excited and emits a gamma raySlows fast neutrons in heavy materials such as U-238 and iron
Radiative capture (n,γ)The neutron is absorbed and a gamma ray is emittedLoss of neutrons; produces Pu-239 from U-238 and activates structures
Particle emission (n,α), (n,p)A charged particle is emittedB-10(n,α) in control materials and BF₃ detectors
Fission (n,f)The nucleus splits, releasing about 200 MeV and 2 to 3 neutronsThe source of reactor power

Microscopic and Macroscopic Cross Sections

The microscopic cross section σ is the effective target area one nucleus presents to a neutron for a given reaction, measured in barns (1 b = 10⁻²⁴ cm²). It is a probability, not a physical size: cadmium presents about 2500 b to a thermal neutron, while carbon presents only 0.0035 b for absorption. The macroscopic cross section Σ combines σ with the number of nuclei per cubic centimetre, N, and is the probability of interaction per centimetre of travel. Its inverse is the mean free path, the average distance a neutron travels between interactions. For a compound, N counts molecules and σ is the sum over the atoms in one molecule.

Atom Density, Macroscopic Cross Section, and Mean Free Path N = ρ N_A / M   (atoms or molecules per cm³; N_A = 6.022 × 10²³ mol⁻¹)
Σ = N σ   (cm⁻¹, with σ in cm²)     Σ_t = Σ_s + Σ_a
λ = 1 / Σ_t   (mean free path, cm)
Large Σ means neutrons interact within a short distance

Beam Attenuation and Reaction Rates

In a narrow, collimated beam, any interaction removes a neutron from the beam, so the uncollided intensity falls exponentially with the total cross section. In a reactor the neutrons move in all directions, and we describe them by the neutron flux φ = nv (neutrons per cm² per second). The rate of any reaction per cubic centimetre is the product of the flux and the macroscopic cross section for that reaction.

Transmission and Reaction Rate I = I₀ e^(−Σ_t x)   (uncollided beam through thickness x)
R = Σ φ   (reactions per cm³ per second)
Thermal power density = Σ_f φ × (3.2 × 10⁻¹¹ J per fission)

Moderation: Slowing Neutrons Down

Fission in U-235 is far more likely for slow (thermal) neutrons near 0.025 eV than for fast ones, so thermal reactors use a moderator to slow neutrons through elastic collisions. A neutron loses the most energy when it hits a nucleus of similar mass: in a head-on collision with hydrogen it can lose all of its energy, but against carbon it keeps at least 72%. The average logarithmic energy loss per collision, ξ, captures this. A good moderator must also scatter often (large Σ_s) and absorb little (small Σ_a); the moderating ratio combines all three properties.

Slowing Down ξ = 1 + [(A − 1)² / 2A] ln[(A − 1)/(A + 1)]   (ξ = 1 for hydrogen)
Number of collisions: n = ln(E₀ / E) / ξ
Slowing-down power = ξ Σ_s     Moderating ratio = ξ Σ_s / Σ_a
Light nuclei slow neutrons fastest; low absorption keeps them alive

Reading Cross-Section and Slowing-Down Graphs

Engineers read nuclear data from graphs. For a 1/v absorber, σ(E) = σ₀ √(0.0253/E), so on log–log axes the cross section is a straight line of slope −0.5. Boron-10 and lithium-6 follow this law, which makes them ideal for thermal-neutron detectors and control materials. Heavy nuclides such as U-238 also show sharp resonances, where the capture cross section jumps by several orders of magnitude at particular energies (the first U-238 resonance is at 6.67 eV). On a slowing-down graph with a logarithmic energy axis, the average energy after n collisions is E₀e^(−nξ), a straight staircase whose steepness is ξ.

Thermal-Neutron Data Used in This Lab (0.0253 eV)

Materialρ (g/cm³)M (g/mol)σ_s (b)σ_a (b)ξ
Light water H₂O (per molecule)1.0018.01544.80.6640.927
Heavy water D₂O (per molecule)1.10520.0310.540.00120.510
Graphite C1.7012.0114.750.00350.158
Iron Fe7.87455.84511.62.560.0353
Cadmium Cd8.65112.415.625200.0177

Values are rounded thermal-neutron data of the kind tabulated in the DOE Fundamentals Handbook (Nuclear Physics and Reactor Theory) and on the Chart of the Nuclides. Molecular values for H₂O and D₂O include both hydrogen atoms and the oxygen atom; for single-atom moderators, ξ for hydrogen is 1.000, deuterium 0.725, beryllium 0.209, and carbon 0.158.

Shielding and control

Cadmium and boron have huge absorption cross sections, which is why they are used in control rods, shutdown systems, and neutron shields.

Moderator choice

Light water slows neutrons quickly but absorbs some; heavy water and graphite absorb so little that they can sustain a reactor on natural uranium.

Industry

Neutron moisture gauges, oil-well logging tools, and neutron radiography all rely on hydrogen slowing neutrons and on materials absorbing them.

Apparatus

The equipment used on a neutron beam line and in moderator studies. In the simulation these are modelled for you, and the readings correspond to what each instrument would show.

Am-Be source
Shielded neutron source
An americium-beryllium source inside a paraffin and borated-polyethylene housing; a collimator lets out a narrow beam.
Collimator
A channel through borated shielding that passes only neutrons travelling along the beam axis.
H₂O · C · Fe · Cd
Sample slabs
Water and heavy-water cells, graphite blocks, iron plates, and cadmium foils of measured thickness.
BF₃2188
BF₃ detector and counter
Thermal neutrons are absorbed by B-10, releasing an alpha particle that ionizes the gas and produces a pulse.
Moderator tank
A tank of moderator in which fast neutrons slow down through repeated elastic collisions.
Chart of the Nuclides
The reference for cross sections, abundances, and half-lives used throughout reactor physics.

Instructions: Running the Virtual Experiment

You are qualifying materials and moderators for a research reactor. The simulation has two immersive 3D work areas and two graph work areas. The parts build from undergraduate work in Parts A to C to graduate-level analysis in the last step of Parts D and E; the level of each part is shown beside its title. In each one you set up the experiment, take readings, work out the answer yourself, enter it, and press Check. Record every reading and prediction in your lab report tables, with a labelled screenshot of each setup. Drag in any 3D view to orbit, and scroll to zoom. Use the data table in the Theory section.

Part A: Atom Density and Macroscopic Cross Section (3D Neutron Beam Bench)Undergraduate
1
Open Simulation → 3D Neutron Beam Bench. Choose Light water. Choose Predict: atom density N, calculate N = ρN_A/M in molecules per cm³, enter it (for example 3.34e22), and press Check.
2
Choose Predict: total macroscopic cross section Σ_t. Calculate Σ_t = N(σ_s + σ_a) × 10⁻²⁴ in cm⁻¹ and check it. Then choose Predict: mean free path and check λ = 1/Σ_t.
3
Repeat for heavy water, graphite, iron, and cadmium. Record ρ, N, Σ_t, and λ for each material in Table A.
Part B: Beam Transmission (3D Neutron Beam Bench)Undergraduate
1
Press Count open beam with no slab to measure I₀. Then select a material and thickness and choose Predict: transmitted fraction. Calculate I/I₀ = e^(−Σ_t x), enter it, and press Check.
2
Press Count with slab and compare the measured ratio of counts with your prediction. Record material, x, predicted and measured I/I₀ in Table B for at least five runs, including 0.5 mm of cadmium and 5 cm of graphite.
3
Choose Predict: absorption rate density. For the flux shown, calculate R = Σ_a φ in reactions per cm³ per second and check it. Explain why cadmium is used for control rods and neutron shields.
Part C: Slowing Down and Moderator Choice (3D Moderator Tank)Undergraduate
1
Open 3D Moderator Tank. Choose a moderator and the starting and final energies. Choose Predict: number of collisions, calculate n = ln(E₀/E)/ξ, enter it, and press Check. Then press Fire neutron to watch one neutron slow down.
2
Choose Predict: moderating ratio. Using ξ, Σ_s, and Σ_a, calculate ξΣ_s/Σ_a and check it. Record the moderator, ξ, n, slowing-down power, and moderating ratio in Table C for hydrogen, deuterium, carbon, light water, heavy water, and graphite.
3
Use Table C to explain why light-water reactors need enriched uranium, while heavy-water reactors can run on natural uranium.
Part D: Cross Section against Energy (Graph: Cross Section vs Energy)Upper undergraduateGraduate step
1
Open Graph: Cross Section vs Energy. Choose Boron-10 and set the energy slider to 0 (E = 1 eV). Check the cross section and the neutron speed, then press Record this run.
2
Check and record: boron-10 near thermal energy (slider −1.6, E = 0.0251 eV), lithium-6 at E = 0.01 eV (slider −2), and uranium-235 fission at 0.1 eV and 10 eV (sliders −1 and 1). Record all runs in Table D.
3
Read the slope of the straight line and check it. Compare the U-238 curve near 6.67 eV with the 1/v lines, and explain in your report why boron-10 is used in BF₃ detectors and control rods while U-238 resonances matter for resonance escape.
4
GraduateA real thermal spectrum is a Maxwellian at the moderator temperature, not a single 0.0253 eV line. Choose Advanced: Maxwellian-averaged cross section and check it for boron-10 at 293.6 K and 573 K, and for uranium-235 fission at 573 K. Record the results under Table D and explain what a hot moderator does to effective absorption.
Part E: Slowing-Down Ladder (Graph: Slowing-Down Ladder)Upper undergraduateGraduate step
1
Open Graph: Slowing-Down Ladder. Keep 2 MeV to 0.025 eV and set k = 10. For hydrogen, check the energy after k collisions, the collisions to reach the target, and the ratio to hydrogen. Press Record this run.
2
Repeat for deuterium, beryllium, and carbon, and record all four moderators in Table E. Compare your collision counts with Table C.
3
From the graph, explain why a graphite-moderated core must be much larger than a water-moderated core. Take a labelled screenshot of the ladder for your report.
4
GraduateDerive ξ from the collision kinematics for a nucleus of mass number A. Choose Advanced: collisions to the target for mass number A and check it for A = 12, 16, 56, and 238 (2 MeV to 0.025 eV). Record the results under Table E and confirm that A = 12 reproduces the carbon value.

Simulation: Neutron Beam Line, Moderator Tank, and Neutron Graphs

Neutron Interactions and Moderation Virtual LabSet up the equipment, work out your answer, then Check

A collimated beam of thermal (0.025 eV) neutrons leaves the shielded source, passes through the sample slab, and reaches the BF₃ detector. Neutrons that interact in the slab are removed from the beam: cyan tracks reach the detector, and the ones that stop in the slab were scattered or absorbed. Parts A and B use this bench.

Drag to orbit · scroll to zoom. 3D beam line: a shielded neutron source and collimator, a sample slab on a stand, and a BF₃ detector with its counter; neutrons that pass through are shown in cyan, absorbed ones stop in the slab.

Setup

Readings

Density ρ—
Molar mass M—
σ_s (scatter)—
σ_a (absorb)—
Open-beam counts I₀ (60 s)—
Counts with slab I (60 s)—
Measured I/I₀—

Detector background is about 2 counts per second and is already subtracted from the counts shown.

Work it out, then check

Tables A and B: your beam-line record
Materialx (cm)N (per cm³)Σ_t (cm⁻¹)λ (cm)Predicted I/I₀Measured I/I₀

A 2 MeV fission neutron enters the moderator tank and slows down through elastic collisions. Its colour changes from red (fast) through orange and green to blue (thermal) as it loses energy, and the counter records each collision. Part C uses this tank.

Drag to orbit · scroll to zoom. 3D moderator tank: a fast neutron enters the tank and zig-zags through collisions with moderator nuclei, changing colour from red (fast) to blue (thermal); the collision counter and energy readout update as it slows.

Setup

Readings

ξ (average log energy loss)—
Σ_s (cm⁻¹)—
Σ_a (cm⁻¹)—
Collisions in last run—
Neutron energy now—

For the bulk moderators, Σ_s and Σ_a are calculated from the data table in the Theory section. The ideal hydrogen and deuterium nuclei are for collision counting only.

Work it out, then check

Table C: your moderator record
ModeratorξE₀ → En (collisions)ξΣ_s (cm⁻¹)ξΣ_s/Σ_a

Most absorbers used in detectors and control rods follow the 1/v law at low energy: the slower the neutron, the longer it spends near a nucleus and the larger the cross section. On log–log axes this law is a straight line. Part D uses this work area.

Absorption cross section against neutron energy on log–log axes: the straight 1/v line of the absorber you chose, with the U-238 capture curve and its 6.67 eV resonance for comparison. The dot marks the energy you set.

Show the plotted values

Setup

Readings

Absorber—
Cross section at 0.0253 eV, σ₀—
Neutron speed at 0.0253 eV—
Energy set—

σ(E) = σ₀ √(0.0253/E) and v = 2200 √(E/0.0253) m/s. The U-238 curve is a simplified training shape around its first resonance.

Work it out, then check

Table D: your cross-section record
AbsorberE (eV)Speed (m/s)σ (b)

Each elastic collision removes, on average, the same fraction of a neutron's logarithmic energy, so on a logarithmic energy axis the average energy falls in equal steps of ξ. The steeper the ladder, the better the moderator slows neutrons. Part E uses this work area.

Average neutron energy against collision number (logarithmic energy axis) for hydrogen, deuterium, beryllium, and carbon, with the target energy shown as a dashed line. The dot marks your chosen moderator after k collisions.

Show the plotted values

Setup

Readings

ξ of this nucleus—
ln(E₀/E_target)—
Target energy—

Average energy after n collisions: E_n = E₀ e^(−nξ). Collisions to reach E: n = ln(E₀/E)/ξ.

Work it out, then check

Table E: your slowing-down record
ModeratorξkE after k (eV)Collisions to targetRelative to hydrogen

These immersive 3D work areas and interactive graph work areas are the main version; the accessible copy delivers the same set-up, work-out, and check exercises with native controls and screen-reader announcements.

Team Questions

Question 1. Reactor-grade graphite has ρ = 1.70 g/cm³ and M = 12.011 g/mol. What is its atom density, in units of 10²² atoms/cm³? (e.g. 8.52)
Question 2. Iron has N = 8.49 × 10²² atoms/cm³, σ_s = 11.6 b, and σ_a = 2.56 b. What is its total macroscopic cross section in cm⁻¹?
Question 3. Cadmium has Σ_t = 117 cm⁻¹ for thermal neutrons. What fraction of a thermal beam passes through a 0.50 mm cadmium foil? (decimal, e.g. 0.0029)
Question 4. How many collisions does a 2 MeV neutron need to slow to 0.025 eV in light water (ξ = 0.927)?
Question 5. How many collisions are needed for the same slowing down in graphite (ξ = 0.158)?
Question 6. Using ξ = 0.158, σ_s = 4.75 b, and σ_a = 0.0035 b, what is the moderating ratio of graphite?
Question 7: Challenge. Light water has Σ_a = 0.0222 cm⁻¹. At a thermal flux of 1.0 × 10¹³ n/cm²·s, how many absorptions occur per cm³ per second, in units of 10¹¹? (e.g. 2.22)

Example Lab Report

Sample report showing the expected format and level of detail. Use it as a guide for your own submission, and include labelled screenshots of each setup. Measured counts will differ slightly from these because neutron emission is random.

Neutron Interactions, Cross Sections, and Moderation

Nuclear Engineering Technology | Section: [Your Section] | Date: [Date]

Lab Members: [Names of all members present]

Purpose

To calculate atom densities, macroscopic cross sections, and mean free paths for reactor materials; to verify exponential attenuation of a thermal-neutron beam; to calculate absorption reaction rates; to compare moderators by the number of collisions needed for thermalization and by their moderating ratio; and to read cross-section and slowing-down graphs the way reactor and detector engineers use them.

Theory

The atom density is N = ρN_A/M, the macroscopic cross section is Σ = Nσ, and the mean free path is λ = 1/Σ_t. A narrow beam is attenuated as I = I₀e^(−Σ_t x), and the reaction rate density is R = Σφ. A neutron needs n = ln(E₀/E)/ξ collisions to slow down, and moderators are compared by ξΣ_s/Σ_a.

N = ρN_A/M  ·  Σ = Nσ  ·  I = I₀e^(−Σ_t x)  ·  n = ln(E₀/E)/ξ

Table A: Atom Densities and Cross Sections Undergraduate

MaterialN (per cm³)Σ_t (cm⁻¹)Σ_a (cm⁻¹)λ (cm)
Light water3.343 × 10²²1.5200.02220.658
Heavy water3.322 × 10²²0.3503.99 × 10⁻⁵2.86
Graphite8.523 × 10²²0.4052.98 × 10⁻⁴2.47
Iron8.491 × 10²²1.2020.2170.832
Cadmium4.634 × 10²²117.0116.80.0085

Sample calculation (light water): N = 1.00 × 6.022×10²³ / 18.015 = 3.343×10²² molecules/cm³; Σ_t = 3.343×10²² × 45.46×10⁻²⁴ = 1.520 cm⁻¹; λ = 1/1.520 = 0.658 cm.

Table B: Beam Transmission (I₀ ≈ 300 000 counts in 60 s) Undergraduate

Materialx (cm)Predicted I/I₀Measured I/I₀
Light water1.000.21880.2185
Heavy water2.000.49640.4971
Graphite5.000.13190.1315
Iron1.000.30050.3009
Cadmium0.050.002880.00285

Absorption rate density in light water at φ = 1.0×10¹² n/cm²·s: R = 0.0222 × 10¹² = 2.22×10¹⁰ per cm³·s.

Table C: Moderator Comparison (2 MeV → 0.025 eV) Undergraduate

Moderatorξn (collisions)ξΣ_s (cm⁻¹)ξΣ_s/Σ_a
Hydrogen nucleus1.00018.2——
Deuterium nucleus0.72525.1——
Light water0.92719.61.3962.5
Heavy water0.51035.70.1794480
Beryllium0.20987.10.159169
Graphite0.158115.20.0640214

Table D: Cross Section against Energy (1/v law) Upper undergraduateGraduate step

AbsorberE (eV)Speed (m/s)σ (b)
Boron-10113 830610.8
Boron-100.025121913855
Lithium-60.0113831495
Uranium-235 fission0.14374294.2
Uranium-235 fission1043 74029.42

Slope of every 1/v line on log–log axes: −0.5. Slider −1.6 gives E = 0.0251 eV, so σ is within 0.4% of σ₀. Include a screenshot of the graph with the U-238 resonance visible.

Graduate step: Maxwellian-averaged cross section σ̄ = (√π/2)σ₀√(293.6/T): boron-10 3403 b at 293.6 K and 2436 b at 573 K; uranium-235 fission 371.1 b at 573 K.

Table E: Slowing-Down Ladder (2 MeV → 0.025 eV, k = 10) Upper undergraduateGraduate step

ModeratorξkE after k (eV)Collisions to targetRelative to hydrogen
Hydrogen1.0001090.818.21.00
Deuterium0.725101 42025.11.38
Beryllium0.20910247 00087.14.78
Carbon0.15810412 000115.26.33

Graduate step: exact ξ(A) and collisions from 2 MeV to 0.025 eV: A = 12, ξ = 0.1578, 115.3 collisions; A = 16, ξ = 0.1200, 151.7; A = 56, ξ = 0.0353, 515.6; A = 238, ξ = 0.00838, 2172.

Discussion

The calculated cross sections show a striking range: one mean free path is 0.66 cm in water but only 0.085 mm in cadmium, so half a millimetre of cadmium removed more than 99.7% of the thermal beam. Measured transmissions agreed with e^(−Σ_t x) to within counting statistics in every case. This huge absorption is why cadmium, boron, and hafnium are used in control rods and neutron shields, while iron, with a moderate Σ_a, is acceptable as a structural material.

Light water slows neutrons in the fewest collisions and has the largest slowing-down power, but its absorption gives it the lowest moderating ratio. Heavy water absorbs so little that its moderating ratio is about 70 times larger, which is why heavy-water reactors can operate on natural uranium, while light-water reactors need uranium enriched to about 3 to 5% U-235. Graphite needs many more collisions, so graphite-moderated cores must be physically large.

The graphs showed the same physics at a glance. On log–log axes every 1/v absorber fell on a straight line of slope −0.5, so boron-10 at 1 eV still absorbs about 611 b; this is why boron is effective in detectors and control rods across the whole thermal range. The U-238 curve rose by about four orders of magnitude at 6.67 eV, which explains why neutrons slowing through the resonance region can be lost to capture. On the slowing-down ladder, ten collisions brought a neutron in hydrogen from 2 MeV to about 91 eV, but left it at about 0.41 MeV in carbon; carbon needed 6.3 times as many collisions as hydrogen, matching the moderator ranking in Table C.

The graduate steps removed two simplifications. Averaging the 1/v cross section over a Maxwellian spectrum gave a value 11% below σ₀ at room temperature, and heating the moderator to 573 K lowered boron-10 absorption to 2436 b, 37% below the tabulated thermal value; reactor codes therefore use spectrum- and temperature-averaged cross sections, and this softening of absorption with temperature feeds into the reactivity coefficients. Deriving ξ from collision kinematics reproduced carbon (115 collisions) and showed why oxygen adds little moderation in water and why heavy fuel nuclei such as U-238 (over 2000 collisions) play no part in slowing neutrons down.

Conclusion

Neutron behaviour in each material followed Σ = Nσ and I = I₀e^(−Σ_t x). Moderators were ranked by slowing-down power (water highest) and by moderating ratio (heavy water highest), linking these cross sections directly to reactor design choices.

Practice Questions

Show all work and include units. Use the data table in the Theory section.

Question 1
Calculate the atom density of U-238 in uranium dioxide fuel (ρ = 10.4 g/cm³, M(UO₂) = 270 g/mol). Each molecule contains one uranium atom.
Hint: find molecules of UO₂ per cm³ first.
Question 2
What thickness of light water reduces an uncollided thermal-neutron beam to 1% of its original intensity?
Hint: x = ln(100)/Σ_t.
Question 3
A sample has Σ_f = 0.10 cm⁻¹ and sits in a thermal flux of 3.0 × 10¹³ n/cm²·s. Find the fission rate density and the power density in W/cm³ (3.2 × 10⁻¹¹ J per fission).
Hint: R = Σ_fφ, then multiply by the energy per fission.
Question 4
Use the formula for ξ to show that ξ for carbon (A = 12) is about 0.158.
Hint: ξ = 1 + [(A − 1)²/2A] ln[(A − 1)/(A + 1)].
Question 5
Explain why light water has the largest slowing-down power but the smallest moderating ratio of the moderators in Table C, and what this means for fuel enrichment.
Hint: compare σ_a for hydrogen and deuterium.
Question 6: Challenge
A neutron moisture gauge counts thermalized neutrons returning from soil. Explain, using ξ and collision numbers, why the count rate rises with the soil's water content.
Hint: hydrogen thermalizes fast neutrons in far fewer collisions than silicon or oxygen.
© 2026 E2 Innovations LLC / Virginia Research Institute. All rights reserved. Licensed for use on E2 Innovations and VRI sites only — not for redistribution or reuse in other courses. Contact info@e2innovations.ai.