Theory: Quality Control of Technetium-99m Radiopharmaceuticals

Why Quality Control Matters

Technetium-99m is used in about 40 000 diagnostic scans every day in the United States. Each dose is prepared in a nuclear pharmacy or hospital hot lab from a Mo-99/Tc-99m generator and a cold kit, and it must pass quality-control tests before release. Impurities do not just waste dose. Free pertechnetate collects in the thyroid and stomach, hydrolysed-reduced technetium collects in the liver, and Mo-99 gives the patient an unnecessary dose from a 66-hour beta emitter. The tests follow USP general chapter <823> and the product monographs, and the results are recorded for every batch.

Part A: Radiochemical Purity by ITLC

A labelled kit, such as Tc-99m medronate (MDP) for bone scans, can contain three chemical forms of technetium:

FormAcetone stripSaline strip
Tc-99m bound to the ligand (wanted)Stays at originMoves to front
Free pertechnetate, TcO₄⁻Moves to frontMoves to front
Hydrolysed-reduced Tc (TcO₂, colloid)Stays at originStays at origin

Each instant thin-layer chromatography (ITLC) strip is spotted at the origin, developed, cut at its midpoint, and the two halves are counted in a well counter. Background is subtracted from each half before the fractions are calculated.

Two-Strip Method % free TcO₄⁻ = net front (acetone) / net total (acetone) × 100
% HR-Tc = net origin (saline) / net total (saline) × 100
RCP = 100 − % free − % HR
Release when RCP ≥ 90% (typical USP monograph limit)

Part B: Radionuclidic Purity (Mo-99 Breakthrough)

A small amount of the parent Mo-99 can wash off the alumina column into the eluate. The eluate vial is first assayed inside a lead shield on the Mo-99 setting. The lead absorbs the 140 keV Tc-99m gammas but lets through part of the 740 and 778 keV Mo-99 gammas, so the reading is multiplied by a shield correction factor. The USP limit is 0.15 µCi of Mo-99 per mCi of Tc-99m at the time of administration.

Breakthrough Ratio and Expiry Mo-99 = shielded reading × correction factor
Ratio(0) = Mo-99 (µCi) / Tc-99m (mCi)
Ratio(t) = Ratio(0) × e^((λ_Tc − λ_Mo)t),  λ = 0.693/t½
Expiry: t = ln(0.15 / Ratio(0)) / (λ_Tc − λ_Mo)
λ_Tc − λ_Mo = 0.11533 − 0.01051 = 0.10482 h⁻¹

Because Tc-99m (t½ 6.01 h) decays much faster than Mo-99 (t½ 65.94 h), an eluate that passes at elution can fail later in the day. Each dose drawn from it must also be decay-corrected: A = A₀e^(−λ_Tc t).

Chemical Purity: Aluminium Ion

Aluminium from the alumina column can interfere with labelling and cause liver or lung uptake. A drop of eluate and a drop of a 10 µg/mL Al³⁺ standard are placed on an indicator paper. The eluate passes if its colour is lighter than the standard.

Planning the Day and Proving Purity

A multidose vial of eluate is limited in three ways at once: the Mo-99 ratio grows as Tc-99m decays, each dose must fit into a practical volume, and the vial itself has a fixed shelf life after elution. The governing limit is whichever is reached first, and it changes with the size of the elution. Single-strip systems separate all three technetium species on one strip, and a strip scanner gives counts in a window for each. Because each window count is a random number, the purity calculated from them has a counting uncertainty: σ falls as 1/√(counts), and a lot near the 90% limit is released only if the lower confidence bound, not just the best estimate, meets the limit.

Apparatus

The equipment in a nuclear pharmacy quality-control area. In the simulation these are modelled for you.

ITLC strips
Silica-gel strips, spotted at the origin and cut at the midpoint after development.
Developing tanks
One with acetone and one with 0.9% saline.
Well counter
NaI(Tl) well detector that counts each strip half.
mCi
Dose calibrator
Ionization chamber with isotope settings for Tc-99m and Mo-99.
Mo-99 assay shield
Lead canister that blocks Tc-99m gammas; supplied with a correction factor.
Aluminium spot-test kit
Indicator paper and a 10 µg/mL Al³⁺ standard.

Instructions: Running the Virtual Experiment

You are the nuclear pharmacist on the morning shift. The simulation has two immersive 3D work areas and two graph work areas. The parts build from undergraduate work in Parts A and B to graduate-level analysis in the last step of Parts C and D; the level of each part is shown beside its title. In each one you set the conditions, work out the answer yourself, enter it, and press Check. Record every reading and calculation in your lab report tables (modelled in the Example Report), with a labelled screenshot of each setup. Drag in any 3D view to orbit, and scroll to zoom.

Part A: Radiochemical Purity (3D ITLC Bench)Undergraduate
1
Open Simulation → 3D ITLC Bench. Choose Lot A and press Develop strips. Write down the four gross counts and the background.
2
Check the % free pertechnetate, the % hydrolysed-reduced Tc, and the radiochemical purity. Press Record this run.
3
Repeat for Lot B and Lot C. Record all three in Table A, decide whether each lot may be released, and name the impurity that causes any failure.
Part B: Mo-99 Breakthrough and Dose Activity (3D Dose Calibrator)Undergraduate
1
Open 3D Dose Calibrator. Choose Elution 1, 1000 mCi, and 6 h. Check the true Mo-99 activity and the ratio at elution.
2
Check the ratio at 6 h, the expiry time, and the Tc-99m activity at 6 h. Note the aluminium spot test. Press Record this run.
3
Repeat for Elution 1 at 800 mCi; Elution 2 at 6 h and 8 h; and Elution 3 at 0 h. Record them in Table B and decide whether each eluate may be used.
Part C: The Multidose Vial through the Day (Graph: Multidose Vial)Upper undergraduateGraduate step
1
Open Graph: Multidose Vial. Choose Elution 1, 1000 mCi, and 6 h. Check the activity concentration, the volume for a 25 mCi dose, and the latest time a dose still fits in 3 mL. Press Record this run.
2
Repeat for Elution 1 at 500 and 1500 mCi, Elution 2 at 1000 mCi (6 h), Elution 3 at 1000 mCi (0 h), and Elution 1 at 300 mCi (2 h). Record every run in Table C.
3
On the graph, find where the concentration curve crosses the 8.33 mCi/mL line and where the breakthrough and 12 h lines fall. State which limit ends the vial's useful life in each case.
4
GraduatePatients are booked every hour from 1 h after elution. For each run in Table C, check the number of hourly 25 mCi doses the vial can supply, applying all three constraints together (3 mL per dose, 10 mL in total, and the earlier of 12 h and the breakthrough expiry). Record it and name the limit that governs.
Part D: Single-Strip Radiochromatogram (Graph: Radiochromatogram)Upper undergraduateGraduate step
1
Open Graph: Radiochromatogram. Choose Lot A and a long scan. From the window counts, check the % HR-Tc, the % free pertechnetate, and the RCP. Press Record this run.
2
Repeat for Lots B, C, and D with a long scan. Compare the RCP of Lots A–C with your two-strip results in Table A. Record all runs in Table D.
3
Look at the trace for each lot and say which peak shows the impurity that causes a failure.
4
GraduateA best estimate above 90% is not proof of purity. For Lot D with a short and a long scan, and for Lot A with a short scan, check the lower 95% confidence bound on RCP from counting statistics. Decide whether each lot can be released, and explain what the pharmacy should do with Lot D after the short scan.

Simulation: Chromatography Bench, Dose Calibrator, and Pharmacy Graphs

Radiopharmaceutical QC Virtual LabSet up the equipment, work out your answer, then Check

A labelled Tc-99m kit must have a radiochemical purity of at least 90% before it is given to a patient. Two strip systems separate the three chemical forms of technetium. Part A uses this work area.

About this work area: Two instant thin-layer chromatography strips are spotted with the labelled kit and developed, one in acetone and one in saline. Each strip is cut at its midpoint and both halves are counted. You choose the kit lot and press Develop strips. The Readings panel gives the gross counts for each half and the background, and every change is announced.

Setup

Readings

Acetone strip: origin half (gross)—
Acetone strip: front half (gross)—
Saline strip: origin half (gross)—
Saline strip: front half (gross)—
Background (per half, same count time)—
Release limit—

Acetone moves only free TcO₄⁻ to the front. Saline moves bound and free Tc to the front; HR-Tc stays at the origin. Subtract background from each half first.

Work it out, then check

Table A: your ITLC record
LotAcetone originAcetone frontSaline originSaline frontFree TcO₄⁻ (%)HR-Tc (%)RCP (%)Release?

Every generator eluate is tested for Mo-99 breakthrough and aluminium ion before use. Because Tc-99m decays faster than Mo-99, the ratio grows with time and the eluate expires. Part B uses this work area.

About this work area: A generator eluate is assayed in a dose calibrator, first in a lead shield that stops the Tc-99m gammas so that only Mo-99 is read, and then unshielded for Tc-99m. You choose the elution, the Tc-99m activity, and the time after elution. The Readings panel gives the shielded reading, the shield correction factor, and the aluminium spot-test result, and every change is announced.

Setup

Readings

Shielded reading (Mo-99 setting)—
Shield correction factor—
Half-lives—
USP limit—
Aluminium spot test—

True Mo-99 = shielded reading × correction factor. Ratio = µCi Mo-99 per mCi Tc-99m. Ratio(t) = ratio(0) × e^((λ_Tc − λ_Mo)t).

Work it out, then check

Table B: your eluate record
ElutionTc-99m (mCi)Mo-99 (µCi)Ratio at elutionTime (h)Ratio at timeExpiry (h)Tc-99m at time (mCi)Al³⁺Release?

One elution fills a 10 mL multidose vial that must supply 25 mCi patient doses through the day. A dose may not exceed 3 mL, the vial expires 12 h after elution, and the Mo-99 ratio must stay within 0.15 µCi/mCi. Part C uses this work area.

About this work area: This graph work area follows a 10 mL multidose vial of eluate through the day. You choose the elution, the Tc-99m activity at elution, and a time. The data table below lists the activity concentration each hour together with the breakthrough expiry and the vial limit, and every change is announced.

Setup

Readings

Vial volume—
Patient dose—
Largest volume per dose—
Vial expiry—
Breakthrough expiry (from Part B)—

C(t) = (A₀/10 mL) e^(−λ_Tc t), λ_Tc = 0.11533 h⁻¹. Training model.

Work it out, then check

Table C: your multidose-vial record
ElutionA₀ (mCi)t (h)C (mCi/mL)Dose volume (mL)Latest time for 3 mL (h)Governing expiry (h)Doses (hourly)

A single-strip system separates all three species on one strip. The strip is scanned, and the counts in three windows give the purity directly. A borderline lot makes the counting statistics matter. Part D uses this work area.

About this work area: This graph work area shows a strip-scanner radiochromatogram. Hydrolysed-reduced technetium stays at the origin, the labelled complex moves to the middle, and free pertechnetate runs with the solvent front. You choose the kit lot and the scan length. The data table below gives the gross counts in each region and the background, and every change is announced.

Setup

Readings

Origin window (Rf 0–0.2), gross—
Middle window (Rf 0.3–0.7), gross—
Front window (Rf 0.8–1.0), gross—
Background per window—
Release limit—

Net = gross − background in each window. Training system with separate windows for each species.

Work it out, then check

Table D: your radiochromatogram record
LotScan% HR-Tc% freeRCP (%)σ_RCP (%)Lower 95% bound (%)Release?

This accessible version provides the same set-up, work-out, and check exercises as the 3D and graph work areas, using native controls, data tables, and screen-reader announcements.

Team Questions

Question 1. An acetone ITLC strip gives 38 520 counts at the origin half and 1600 counts at the front half. Background is 120 counts per half. What is the % free pertechnetate?
Question 2. The saline strip of the same kit gives 2520 counts at the origin half and 33 720 counts at the front half (background 120). What is the % hydrolysed-reduced Tc?
Question 3. What is the radiochemical purity of this kit, in %? Can it be released?
Question 4. An eluate of 800 mCi Tc-99m reads 16 µCi in the Mo-99 shield, whose correction factor is 2.5. What is the breakthrough ratio, in µCi/mCi?
Question 5. What is that ratio 5 hours after elution? Use λ_Tc − λ_Mo = 0.10482 h⁻¹.
Question 6. How many hours after elution does that eluate reach the 0.15 µCi/mCi limit?
Question 7: Challenge. A patient needs 20 mCi of Tc-99m MDP at 10:00. The dose is drawn at 07:00. What activity must be drawn, in mCi?

Example Lab Report

Sample report showing the expected format and level of detail. Use it as a guide for your own submission, and include labelled screenshots of each setup.

Radiopharmaceutical Quality Control

Nuclear Chemistry | Section: [Your Section] | Date: [Date]

Lab Members: [Names of all members present]

Purpose

To find the radiochemical purity of Tc-99m MDP kits by two-strip ITLC, and to test generator eluates for Mo-99 breakthrough, expiry time, decay-corrected activity, and aluminium ion, to plan the use of a multidose vial against all of its limits, and to read a single-strip radiochromatogram and make a statistically sound release decision.

Theory

Acetone moves only free pertechnetate; saline leaves only hydrolysed-reduced Tc at the origin. The Mo-99/Tc-99m ratio grows with time because Tc-99m decays faster.

RCP = 100 − %free − %HR  ·  Ratio(t) = Ratio(0)e^(0.10482t)  ·  A = A₀e^(−0.11533t)

Table A: ITLC Results (background 120 counts per half) Undergraduate

LotAcetone originAcetone frontSaline originSaline frontFree TcO₄⁻ (%)HR-Tc (%)RCP (%)Release?
A39 320920120035 0402.003.0095.00Yes
B37 5202720156034 6806.504.0089.50No
C39 720520390032 3401.0010.5088.50No

Table B: Eluate Results (shield correction factor 2.5) Undergraduate

ElutionTc-99m (mCi)Mo-99 (µCi)Ratio at elutionTime (h)Ratio at timeExpiry (h)Tc-99m at time (mCi)Al³⁺Release?
1100030.00.03006.00.056315.35500.6PassYes
180030.00.03756.00.070313.23400.5PassYes
2100075.00.07506.00.14076.61500.6FailNo
2100075.00.07508.00.17356.61397.5FailNo
31000175.00.17500.00.17500.001000.0PassNo

Table C: Multidose Vial (10 mL, 25 mCi doses, ≤ 3 mL each) Upper undergraduateGraduate step

ElutionA₀ (mCi)t (h)C (mCi/mL)Dose volume (mL)Latest time for 3 mL (h)Governing expiry (h)Doses (hourly)
110006.050.060.49921.5512.0012
15006.025.030.99915.548.748
115006.075.090.33325.0612.0012
210006.050.060.49921.556.616
310000.0100.000.25021.550.000
13002.023.821.05011.113.873

Graduate step: the dose count (last column) applies all three limits together. The 12 h vial limit governed for 1000 and 1500 mCi (12 doses, 6.86 and 4.58 mL used); Mo-99 breakthrough governed for 500 mCi (8.74 h, 8 doses), for Elution 2 (6.61 h, 6 doses), and for 300 mCi (3.87 h, 3 doses); Elution 3 supplied no doses. Elution 2 also fails the aluminium test, so in practice none of its doses may be used.

Table D: Single-Strip Radiochromatogram (background 150 counts per window) Upper undergraduateGraduate step

LotScan% HR-Tc% freeRCP (%)σ_RCP (%)Lower 95% bound (%)Release?
ALong3.002.0095.000.19394.68Yes
BLong4.006.5089.500.24389.10No
CLong10.501.0088.500.25088.09No
DLong4.904.5090.600.23490.21Yes
DShort4.904.5090.601.29088.48No (not demonstrated)
AShort3.002.0095.001.26292.92Yes

Graduate step: σ_RCP from the propagated counting variances (var n = G + B in each window); lower bound = RCP − 1.645σ. Lot D's best estimate of 90.6% passes, but after a short scan the purity is not demonstrated (88.48%); the long scan demonstrates it (90.21%).

Discussion

Only Lot A met the 90% limit. Lot B failed because of free pertechnetate, which usually means the stannous reducing agent was oxidised, for example by air entering the vial. Lot C failed because of hydrolysed-reduced technetium, which can come from too much stannous ion or moisture in the kit. Lot C's free pertechnetate was low, so a single acetone strip would have passed it; both strips are needed. Background subtraction mattered most for the small fractions: without it, Lot A's free pertechnetate would read 2.29% instead of 2.00%.

Elution 1 passed with a wide margin, and a smaller activity of Tc-99m made the ratio larger and the expiry earlier. Elution 2 passed for Mo-99 at 6 h but would exceed the limit by 8 h, since its expiry was 6.61 h, and it failed the aluminium test, so it could not be used at all. Elution 3 failed for Mo-99 at the moment of elution. Every test must pass for an eluate to be used.

The multidose-vial graph turned the breakthrough rule into a working schedule. A large elution was limited only by the 12 h vial expiry, but a 500 mCi elution expired by Mo-99 breakthrough at 8.74 h, because a smaller Tc-99m activity makes the ratio start higher. The single-strip radiochromatogram gave the same RCP values as the two-strip method for Lots A–C and showed each impurity as its own peak.

The graduate steps showed that release decisions must account for uncertainty. Combining all three vial limits gave the number of patients each elution could actually serve. For Lot D, a best estimate of 90.6% looked acceptable, but after a short scan the lower 95% bound was only 88.5%, so purity was not demonstrated; a ten-times-longer scan cut σ by about √10 and demonstrated a bound of 90.2%.

Conclusion

Two-strip ITLC identifies both radiochemical impurities, and the Mo-99 ratio must be checked at the time of administration, not only at elution, because it grows by about 11% per hour.

Practice Questions

Show all work and include units.

Question 1
An acetone strip gives 30 000 net counts at the origin and 1200 net counts at the front. A saline strip gives 900 net counts at the origin and 29 100 at the front. Find the RCP.
Hint: find % free and % HR separately, then subtract both from 100.
Question 2
Why is a single acetone strip not enough to find the radiochemical purity of a Tc-99m MDP kit?
Hint: where does hydrolysed-reduced Tc go on an acetone strip?
Question 3
An eluate has a ratio of 0.10 µCi/mCi at elution. What is the latest time it may be used?
Hint: t = ln(0.15/0.10)/0.10482.
Question 4
Why does the Mo-99 lead shield need a correction factor?
Hint: the shield also absorbs part of the Mo-99 gammas.
Question 5
A 25 mCi dose was calibrated for 09:00 but is given at 11:30. What activity does the patient receive?
Hint: A = A₀e^(−0.11533 × 2.5).
Question 6
Name one organ where each impurity (free pertechnetate, HR-Tc, Mo-99) would give the patient an unwanted dose.
Hint: see the Theory section.